Friday, October 27, 2023

Phew, just made it.

I did get my extended lunch yesterday, so I went home and worked on the back window for the cap.  Unfortunately, being in a rush, I got a little sloppy with the saw.  D'oh!  Fortunately it only hit plastic.


I also got lazy while in a rush, and decided to cut the hinge with my circular saw.  It went through the metal like butter.  It pays to buy nice blades.


I got the acrylic cut for the back before I had to go back into work.  


When I got home, it was assembly time.  It was after dark when I finished, but I got most of it done before it got dark.  


Turns out the handle for my outdoor broom is the perfect length to wedge in the corner of the bed and hold it open.  


Next up were the latches.  


Once I got the lid completed, I went to Hannaford to pick up the fresh stuff I wanted to bring.  It won't last the whole trip, but at least I will have some fresh veggies and whatnot for the first week or so.  I took that opportunity to test charging the Jackery while driving.  It worked just fine.  I am guessing it is limited to 100W on the 12V plug; I was getting around 80W but also have pretty significant voltage loss due to the length of the wires.  Still, the fridge only draws 40-50W when running, so it should be fine.  


And with that, the cap is complete.  It is still a bit tight, so hopefully it doesn't rain a lot and the wood expands, I might sand the sides down at some point in the future, but it won't be before this trip.  

The other big things were to get the GoPro setup.  That didn't go as planned.  I hope people weren't too attached to the en route videos I made on the last trip.  


Turns out the roof of my truck is aluminum, or at least something that isn't magnetic.  I tried my magnetic light on it, and it didn't stick either.  So going forward I will need to come up with a new way to mount the GoPro.  


I also started loading up the back.  It isn't quite finished I will finish it up today before I leave.  But all that is left is the second suitcase (I did all my laundry last night and packed the suitcase, I just didn't put it in the truck), and the fridge and microwave.  The spot on the left in the front is for the Jackery and fridge.  


This is likely my last post until after the trip, so no updates for a while.  I will be leaving work early, and finishing up the last couple of things, most notably the packing and the hot tub.  

Current To-do:
  • Trip:
    • Tonight - Drain hot tub and pack it away.
    • Do something with ditch in back
    • Go to Tractor Supply and finish out the mortgage.
    • Dump run
    • Friday - Turn off Synology
    • Friday - Turn on furnace/heat
    • Tonight - Pack clothes (26 days).  Buy clothes if needed.
    • Pack everything else.
    • Put cap on truck
    • Today - Build back window for cap
    • Postponed - Install basics, like lighting and window locks in cap.  - Don't need it for this trip.
    • Wednesday - Test cap.  Make sure it doesn't go explody at 80mph
    • Tonight - Test wiring for Jackery and fridge.
    • Tonight/Friday - Load truck.
    • Thursday - Print out directions
    • Thursday - Finish making hotel reservations
    • Set up GoPro control from my new phone.
    • Upon my return - Get haircut
    • Upon my return - Empty portable toilet.  Don't need it for this trip.
    • Have Barry come chop up the logs
  • After trip, but preferably before winter:
    • Install drainage in the backyard.  
    • Shorten PTO shaft for snowblower
    • Insulate the water lines
    • Take scrap metal to Buffum
    • Close up tiny home.
    • Final mowing of leaves. 
    • Winterize equipment
  • Winter projects: 
    • All the cabinet upgrades (bathroom, pantry, and kitchen)
    • Design deck
    • Build armoire
    • Install whole house filter
    • Shelving upgrades in master closet.
    • Access panel upgrades in master closet
    • Install cube organizer in living room
  • 2024 Projects:
    • Deck
    • Entertainment center
    • Storm doors

Thursday, October 26, 2023

Cap reinforcements. Working in the dark isn't fun.

I didn't get to go out yesterday at lunch (I didn't get a lunch at all yesterday actually) so I didn't get a chance to build the back window, but I still got some stuff done during the day yesterday.  While I was in a call, I finished making the hotel reservations, and got the directions all printed out.  


Since Home Depot didn't have any c-clamps, I ended up going to Harbor Freight.  I saw an interesting vehicle while I was there.  There was a coffin in the back too.  


I didn't get home until after dark.  Since I am out of time, I decided to work on the cap anyways.  I got screws put in the sides of the windows.  I also taped up the broken section.  


That got me thinking, why not tape all the corners and seams.  So I did that too.


Dad and I had very similar ideas for how to attach the corner that the clamp didn't fit.  His way was stronger, but mine was simpler, just a ratchet strap and hook eye. The straps aren't as strong, but a strap is still stronger than the hook eye (which are only rated for ~250lbs).  


I stuffed the leftover strap into one of the crevices of the bedliner.


While I was at it, I added two more C clamps in the middle.  


So it now has 6 attachment points.  It was solid before, now it will be solid even if one (maybe even two depending on which two) of the clamps loosens up with vibration.  


I also added some extra bracing in the back corners.  


The other one was square, this side is as bad as it looks.


I took one of my longer bungee cords and hooked it from the front to the back.  This way when I load it up I have something to attach things to.


The last thing I did was I ran the 12V extension wire.  The idea here is that I have a 12V charger for the Jackery, and I am hoping that I won't have to lug the Jackery out to plug it in every night.  On days when I drive a lot, the 12V charging will hopefully top it off.


I am still trying to deflate the hot tub.  I made some progress, but I think I am going to need a vacuum to finish it off; it won't do it on its own. 

I tested the cap on my way in to work today.  The whistling is still present, but is quieter now.  The vibration is still present, but it doesn't vibrate until about 75mph now, and isn't bad even then.  While it means I will be slow out west where the speed limits are 80mph, that should be fine.  The cap has a surprising amount of drag on it, so I probably won't be going 85+ anyways.

I plan on taking an extra long lunch break today (and already cleared my work calendar for it), so I should be able to build the back window.  Time is running short, but the list of tasks is dwindling down as well.  Some things, like the lighting, I may not bother.  The truck's bed light is more than sufficient, and I don't plan on sleeping in the back of the truck on this trip; my cot was one of the mold casualties so I will be sleeping in the cab the couple of nights I will be in the truck.  The only planned nights in the truck are Friday night, and the last couple of nights on the way back to KY.  You can see the itinerary here: https://docs.google.com/document/d/1yxWkIWb0KuOD_Q4MdSrbRjjhJUyD5iByeS89gjjEwwI/edit?usp=sharing

Current To-do:
  • Trip:
    • Tonight - Drain hot tub and pack it away.
    • Do something with ditch in back
    • Go to Tractor Supply and finish out the mortgage.
    • Dump run
    • Friday - Turn off Synology
    • Friday - Turn on furnace/heat
    • Tonight - Pack clothes (26 days).  Buy clothes if needed.
    • Pack everything else.
    • Put cap on truck
    • Today - Build back window for cap
    • Postponed - Install basics, like lighting and window locks in cap.  - Don't need it for this trip.
    • Wednesday - Test cap.  Make sure it doesn't go explody at 80mph
    • Tonight - Test wiring for Jackery and fridge.
    • Tonight/Friday - Load truck.
    • Thursday - Print out directions
    • Thursday - Finish making hotel reservations
    • Set up GoPro control from my new phone.
    • Upon my return - Get haircut
    • Upon my return - Empty portable toilet.  Don't need it for this trip.
    • Have Barry come chop up the logs
  • After trip, but preferably before winter:
    • Install drainage in the backyard.  
    • Shorten PTO shaft for snowblower
    • Insulate the water lines
    • Take scrap metal to Buffum
    • Close up tiny home.
    • Final mowing of leaves. 
    • Winterize equipment
  • Winter projects: 
    • All the cabinet upgrades (bathroom, pantry, and kitchen)
    • Design deck
    • Build armoire
    • Install whole house filter
    • Shelving upgrades in master closet.
    • Access panel upgrades in master closet
    • Install cube organizer in living room
  • 2024 Projects:
    • Deck
    • Entertainment center
    • Storm doors

Wednesday, October 25, 2023

The cap lives.

I was tinkering with the hot tub yesterday when I went home for lunch to make the final run to the dump.  Turns out I didn't remove the valve, it is a two part valve.  It has deflated a bit more since the last picture, but it is still standing on its own.  


The replacement stairs came in yesterday, despite Amazon claiming they wouldn't be in until December.  I walked up them and they didn't buckle this time.


I left work a little early and helped Barry get the rest of the wood.  We loaded my truck to the brim.  It felt like it was somewhere around 2500 lbs based on how the truck was handling.  


After that he helped me put the cap on and get the gasket on it.  The side on the right looks a little bent, but it fits properly.  Maybe I will add a brace just to keep it from bending further.


I also put screws in the windows since I was going to replace them anyways, and haven't installed the latches.  


He expressed concern about there not being any material here, and if I am driving in the rain, will the natural curve of the truck push water up there.  I hope not, but I guess we will find out.  I had a shelf there in my final design, but that was a "after I get the raise portion for the bed installed" task.  


I got it clamped down, but I don't like how little of the wood it is biting.  Thus far it hasn't been a problem though.  


I couldn't get the clamp on over here.  Unlike the back, there isn't play in the front.  I will have to come up with an alternative solution for holding this corner down.  I am currently driving with only 3 clamps, which is playing with fire.  


I took it for a test run around the block though, and everything survived.  It was quite solid, even with me doing a slalom in the road.


I also made a run to Home Depot to get the parts for the rear window.  Turns out it starts whistling at around 40-45mph, and starts vibrating at 60-65mph.  I assume the whistling is  the window that is broken, and the vibrating is the sides of the windows (I only put screws in the bottom to close them).  On a side note, the truck's bed light easily illuminates the whole thing.  I should be able to fix both of those today.  


After I got home from the run to Home Depot, I finished up some more packing.  


I am still worried about time, but at this point I am mostly ready.  Tonight I will go and pick up the fresh veggies and whatnot I intend to bring and build the back window, and then tomorrow is the last load of laundry.  Friday I will do the final shut down of everything and make sure the furnace is running as a backup and that kind of stuff, and take off Friday evening.

Current To-do:
  • Trip:
    • Drain hot tub and pack it away.
    • Do something with ditch in back
    • Go to Tractor Supply and finish out the mortgage.
    • Dump run
    • Friday - Turn off Synology
    • Friday - Turn on furnace/heat
    • Thursday - Pack clothes (26 days).  Buy clothes if needed.
    • Pack everything else.
    • Put cap on truck
    • Wednesday - Build back window for cap
    • Wednesday - Install basics, like lighting and window locks in cap.
    • Wednesday - Test cap.  Make sure it doesn't go explody at 80mph
    • Thursday - Test wiring for Jackery and fridge.
    • Thursday - Load truck.
    • Thursday - Print out directions
    • Thursday - Finish making hotel reservations
    • Set up GoPro control from my new phone.
    • Upon my return - Get haircut
    • Upon my return - Empty portable toilet.  Don't need it for this trip.
    • Have Barry come chop up the logs
  • After trip, but preferably before winter:
    • Install drainage in the backyard.  
    • Shorten PTO shaft for snowblower
    • Insulate the water lines
    • Take scrap metal to Buffum
    • Close up tiny home.
    • Final mowing of leaves. 
    • Winterize equipment
  • Winter projects: 
    • All the cabinet upgrades (bathroom, pantry, and kitchen)
    • Design deck
    • Build armoire
    • Install whole house filter
    • Shelving upgrades in master closet.
    • Access panel upgrades in master closet
    • Install cube organizer in living room
  • 2024 Projects:
    • Deck
    • Entertainment center
    • Storm doors

Tuesday, October 24, 2023

Need more time.

Yesterday when I got home from work, Barry had finished up all the cutting and had already left, so I finished dumping the hot tub instead.  Apparently some of the foam board stuck to it, which I thought was a bit odd.  


I also got the pump and whatnot disconnected.  This will probably go inside with the pool stuff.  


Next up was dealing with the ditch.  Everything is still soup though from the large amount of rain we got over the weekend.


I also had to relocate the back steps.  


I got most of the ditch filled in.  I might try to pack it some if I get time, but if not this is still acceptable.



I tried to take a pano shot, but it looks poorly stitched and has a weird bump in the middle.


I was fortunate not to have a tire punctured.  That is a pick, just randomly dug up in the back yard.


The sunset was gorgeous last night.  Here are a few pictures.


And I took a short video of the clouds.


I also snagged a picture of the last rays of sunlight filtering through the trees.  I don't get great color on my lot (everything on my lot just turns yellow, all my maples kicked the bucket) but it still looks pretty.



I was hoping that the hot tub would deflate itself (it started to) but when I left this morning it hadn't.  I am not sure how to deflate it (without sharp or pointy implements), I pulled the valve that is supposed to do it. Time is running short, but I hope to get the cap put on the truck today.  Building a box shouldn't take long, and I already have the hinges and latch.

Since it was quite long, and time is really short, I cleaned up the list a bit.
Current To-do:
  • Trip:
    • Drain hot tub and pack it away.
    • Do something with ditch in back
    • Go to Tractor Supply and finish out the mortgage.
    • Dump run
    • Turn off Synology
    • Turn on furnace/heat
    • Pack clothes (26 days).  Buy clothes if needed.
    • Pack everything else.
    • Put cap on truck
    • Build back window for cap
    • Install basics, like lighting and window locks in cap.
    • Test cap.  Make sure it doesn't go explody at 80mph
    • Test wiring for Jackery and fridge.
    • Load truck.
    • Print out directions
    • Finish making hotel reservations
    • Set up GoPro control from my new phone.
    • Get haircut
    • Empty portable toilet.
    • Have Barry come chop up the logs
  • After trip, but preferably before winter:
    • Install drainage in the backyard.  
    • Shorten PTO shaft for snowblower
    • Insulate the water lines
    • Take scrap metal to Buffum
    • Close up tiny home.
    • Final mowing of leaves. 
    • Winterize equipment
  • Winter projects: 
    • All the cabinet upgrades (bathroom, pantry, and kitchen)
    • Design deck
    • Build armoire
    • Install whole house filter
    • Shelving upgrades in master closet.
    • Access panel upgrades in master closet
    • Install cube organizer in living room
  • 2024 Projects:
    • Deck
    • Entertainment center
    • Storm doors

Monday, October 23, 2023

Busy weekend.

Thursday I went and got the last load of gravel.  Like last time I got to watch the sun set through the trees as I unloaded it.  We are at the point of the year where I don't have daylight when I get home.  




This whole load went into the driveway.  It isn't enough, but will do until spring when I can get a dump truck delivered.



My hiking poles and stuff for the trip came in.  My old ones were among the mold casualties.  To get free shipping, I also added a cube storage thing.  It looks like it will match the wallpaper in the house.  


I plan to put it here to empty out those totes.  That will be a winter project though.


I took Friday off, and slept in.  I was a bit behind on sleep.  I mostly did trip stuff on Friday, and returned the steps, stuff like that.  I went and rearranged the stuff in the carport so it all fit better too, though I didn't snag a picture.  I did some other errands too, like drop off my dress clothes for dry cleaning.  I also tore up and fixed my driveway trying to drive up to the shed.  At least I know my truck has a locking diff now.


While I was moving stuff around, one of my pairs of jeans had a fatality.  I needed all them to survive for the trip though, so I also went and had to pick up another pair.


I also went and got all the information for the e-bike warranty.  They claim they are going to send me a new wheel (with a new hub motor).  We shall see, but at this point I probably won't be able to test it until spring.  They had me disassemble the wiring and look at it.  It looked fine.  


I also got my stuff out of the tiny home that I will need for the trip. 


I started to look at the trench in the back in the afternoon.  I got the bit dug for the downspout for the gutters I don't have yet.  


I checked to see whether I had enough drop.  Turns out I had too much.  Way too much.  While that isn't a problem for water flowing, it means to maintain drop all the way to the end I would have to bury the far end of the pipe many many feet deep.  I started to fill it in, but didn't get very far.


One last thing I did during a break from digging on the trench is that I got the back of the truck raked out.  I bought this little rake to rake rocks out of the yard since the bo rake doesn't do grass well.  It works well at cleaning out the back of the truck though.  Very well actually.  


I parked the truck on the hill to let the rain try to clean it off a bit.  


Since I was tired of digging, I also went and clipped all the branches and small trees up here.  They were constantly whacking the truck since I have to pull up here to back into the parking spot.  


Saturday was wedding day.  And wet.  The drainage ditch was already filling up.  


On the plus side, the rain took a lot of the dirt out of the back of the truck.  


I finished up my meal prep in the morning when the rain started back up.  All that is left on the food front now is the fresh vegetables, which I will pick up later in the week.


The pumpkin festival in Keene was also on Saturday, so I walked around a bit on the way to the wedding.


I won a potato at the wedding.  There was a game of hot potato at the reception, and I came in second place.  First place got the decorations on the table.  


I think I prefer the potato.  It was tasty Sunday morning.  


After cooking breakfast, I also loaded up the ridge and freezer.  I am definitely at the limit for freezer space.  



There is still a little space in the fridge though.


The big items for Sunday were the snowblowers.  I got the oil changed in the walk behind.  I have no idea what makes oil look like that.  


There was oil in it too thankfully.


When it was all done, it actually looks kind of neat.  Not great to be running in an engine, but still looks neat.


I kind of wonder if they intentionally made everything difficult to do.  The drain plug would have been much easier to remove if the pipe were another 2 inches longer, and they intentionally buried the oil fill into the corner of the gas tank.


I was a little surprised that the bar had grease fittings, so I went to grease it.  The first one must have given up in shock since the fitting came out.  

It looked like a pound in type, so I beat it back in.  


The other one still had manufacturer paint on it.  They had clearly never been used.  I also replaced the D clips with real shear pins.


I got the skids adjusted, and the walk behind is ready to go.  


Next up was the big snowblower.  I got it all greased up, oiled the chain, and so on.  It was probably done at the factory, but I figured it wouldn't hurt.  


I tried to get my grease gun into this gearbox, but it didn't fit.  I squirted some motorcycle chain oil in there instead.  


I still haven't found my old diesel additive, but thankfully I picked up a new bottle while I was at tractor supply.  I really need to find all that stuff.


I also got the cutting edge reversed, which you are supposed to do for gravel driveways.  This is a really beefy cutting edge.


After that was done, I did more trip prep.  The toolbox is now setup.  


I also got the laundry set up.  The plan is that when I stop, I only need to bring in the red bag and my backpack, and possibly a small bag for food.  The red bag has two weeks of clothes, along with my hiking stuff and coats and whatnot.


I also got most of the hotels booked, all the way to Zion.  I really shouldn't have waited this long to do that, I had to redo the hotel search for most of the stops.

I also went to the car wash, and got the truck cleaned out.  After the rain, it went pretty quickly.  


I also enjoyed the hot tub for the last time this year.  I noticed when I opened it up that the rain had partially refilled the tub.  So much for the lid.  If I weren't taking it down, I probably would have rebalanced it.  I might build a new lid for it next year.


I brought out a brush to try to scrub some of the discoloration out.  I didn't get very far.


Final tally for power is 238kWh (which comes out to $57.12 of power).  For 22 days of fall weather, that isn't bad.  A touch higher than I was hoping for, but not unreasonable.  Not considering that it has been cold enough after the first week that I have been running the heat in the house.


After I was done lounging in it last night, I pulled the drain.  It drains pretty slowly, but considering I am dumping 250 gallons, probably not a bad thing.  


While I was waiting for it to drain, I replaced the wipers on my truck.  That was something that I definitely wanted to do before the trip.  


I also started pulling together all the other stuff I am bringing on the trip.  


A lot of the things needed to charge.


It was still draining when I went to bed.  


There was still water in the bottom this morning, but I think I will need to tip it to get that out.  I will do that tonight.


Despite the wedding, I got a lot of things checked off.  I think for the ditch in the back, I might just fill it in with the tractor and eat the loss on the excavator and deal with it next week.

Current To-do:
  • Trip:
    • Make sure my formal clothes can be found and still fit.
    • Drain hot tub and pack it away.
    • Hook up snowblower to tractor
    • Do something with ditch in back
    • Go to Tractor Supply and finish out the mortgage.
    • Dump run
    • Turn off Synology
    • Turn on furnace/heat
    • Pack clothes (26 days).  Buy clothes if needed.
    • Pack everything else.
    • Pack food.
    • Clean out truck
    • Wash out bed
    • Put cap on truck
    • Build back window for cap
    • Install basics, like lighting and window locks in cap.
    • Test cap.  Make sure it doesn't go explody at 80mph
    • Test wiring for Jackery and fridge.
    • Load truck.
    • Print out directions
    • Finish making hotel reservations
    • Set up GoPro control from my new phone.
    • Get haircut
    • Empty portable toilet.
  • Before winter:
    • Move carport
    • Fix carport
    • Final grade - get gravel and drainage pipe.
    • Buy a real bed and living room furniture.
    • Get a gun cabinet/safe.
    • Fix driveway.
    • Install drainage in the backyard.  
    • Remove the backflush hose.
    • Get heat pump installed.
    • Get a snowblower for the tractor.
    • Build a platform for the steps.
    • Insulate the water lines
    • Have Barry come chop up the logs?
    • Take scrap metal to Buffum
    • Clean out and take down portable garage.
    • Remove the tow straps embedded in the carport.
    • Drain hoses and put away for winter.
    • Get rid of those steps for the hot tub.  
    • Close up tiny home.
    • Install driveway markers.
    • Final mowing of leaves. 
    • Winterize equipment
  • Winter projects: 
    • All the cabinet upgrades (bathroom, pantry, and kitchen)
    • Design deck
    • Build armoire
    • Build dresser
    • Install whole house filter
    • Shelving upgrades in master closet.
    • Access panel upgrades in master closet
    • Install cube organizer in living room
  • 2024 Projects:
    • Deck
    • Entertainment center
    • Storm doors